hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 1 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) 1. product overview general description the hfdom4 0 p - xxxsx series 4 0 pin flash disk module is a flash technology based with true ide interface flash memory card. it is constructed with flash disk controller chip and nand - type (samsung) flash memory d evice. the hfdom 40 p - xxxsx series operates in both 3.3 - volt and 5.0 - volt power supplies. it comes in capacity of 8, 16, 32, 64, 128, 192, 256 mb and up to 384 mb formatted 40 pin type . by optimizing flash memory management, the life of this hfdom 40 p - xxxsx s eries can be extended to its maximum level. because the ecc function is included, the correctness of data transfer between the hfdom 40 p - xxxsx series and a true ide compatible interface device can be guaranteed. the hfdom 40 p - xxxsx series is fully compatib le with applications such as cpu card / board, set top box, industry / military pc / notebook, security equipment, measuring instrument and embedded systems. features - true ide compatible host interface - direct plug in for 3 .5 2 ide con nectors - 40 pin 2 .54 mm ide connector - very high performance, very low power consumption - automatic error correction - support 3 power save mode : stop/idle/active - support for cis implemented with 256 bytes of attribute memory - 3.3v/5.0v operation voltage - host da ta transfer rate : 20mb/s - flash data transfer rate : 10mb/s - host interface bus width : 8/16 bit access - flash interface bus width : 8 bit access - capacity : min. 8 mb ~ max. 384 mb - mtbf : 1,000,000 hours, minimum 30,000 insertions - operating vibration : 15g pea k to peak maximum - operating shock : 1,000g maximum product specifications capacities : 8 , 16, 32, 64, 128, 192, 256 and up to 384 mb (formatted) operating voltage : 3.3v / 5.0v 10% power consumption s : read mode 30 ma (typ), 5 0 ma (max) write mode 3 0 ma (typ), 7 0 ma (max) stop mode 30 u a (typ) environment conditions : operating temperature 0 c to + 6 0 c storage temperature - 2 5 c to + 85 c relative humidity 95%(max) mechanical conditions : weight : maximum 9 .0g 4 0 pin flash disk module min. 8 mb ~ max. 384 mb, true ide interface mode, 3.3v / 5.0v operating part no . hfdom4 0p - xxxsx
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 2 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) electrical specifications table 1.1 absolute maximum ratings symbol parameter ratings unit v dd supply voltage - 0.3 to + 7.0 v v in input voltage - 0.3 to + 7.0 v i in dc input current - 10 ma t stg storage temperature - 20 to + 85 c table 1.2 recommended operating conditions symbol parameter ratings unit 5v 4.75 to 5.25 v v dd dc supply voltage 3.3v 3.0 to 3.6 v t a storage temperature - 20 to +70 c table 1.3 dc characteristics (ta=0 c to 70 c, v dd =3.0 to 5.3v) symbol parameter min. typ. max. unit i dd operating curren t 30 70 ma i ds stop current 50 150 m a v dd high level output voltage 2.4 v v dd low level output voltage 0.4 v capacity specifications table 1.4 capacity specifications part number capacity ( unfo r mat t ed ) total s ector cylinders heads sectors hfd om 40 p - 0 08 sx 7,864,320 bytes 15,360 30 16 32 hfdom 40 p - 016sx 15,990,784 bytes 31,232 61 16 32 hfdom 40 p - 032sx 32,243,712 bytes 62,976 123 16 32 hfdom 40 p - 064sx 65,536,000 bytes 128,000 250 16 32 hfdom 40 p - 128sx 131,858,432 bytes 257,536 503 16 32 hf dom 40 p - 192sx 196,608,000 bytes 384,000 750 16 32 hfdom 40 p - 256sx 265,027,584 bytes 517,632 1011 16 32 hfdom 40 p - 384sx 395,837,440 bytes 773,120 1510 16 32
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 3 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) 1 2 3 + - jump er 1 physycal specification s 51.85 0.1 mm 22.10 0.1 mm 29.0 0.2 mm 7. 0 0.1 mm 55.3 7 0.1 mm < view from front side > 3. 8 0.1 mm 2 .54 0.05 mm 6 . 0 0.1 mm 2.54 0.05 mm 48.20 0.1 mm 55.30 0.1 mm < view from connector side > figure 1.1 40 pin type flash disk module dimensions jumpe r master slave 1,2 close 2,3 close
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 4 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) installtion guide 1 ) setting method make sure your computer is turned off before you open the case. plug the carefully into the 40 pin ide slot on your computer . caution: make sure to align pin1 on host adapter interface connector with pin 1 on your flash disk module . pin 1 is indicated by a triangle on the flash disk module connector. t he flash disk module is use d power connector cable of the compu ter. caution: if you need to remove your flash disk module , use both hands to pull it out carefully . check all cable connections and then replace your computer cover. 2 ) bios setting method before you format or partition your new drive, you must configure your computer's bios so that the computer can recognize your new drive. turn your computer on. as your computer start up, watch the screen for a message describing how to run the system setup program on the screen (sometimes called bios or cmos setup). thi s is usually done by pressing a special key, such as d elete , e sc or f1 during startup. see your computer manual for details. press the appropriate key to run the system setup program. if your bios provides automatic drive detection (an "auto" drive type), select this option. ( we recommend to use normal / chs mode to partition your flash disk module to get the maximum formatted capacity. ) this allows your computer to configure itself automatically for your new drive. if your bios dose not provide auto dr ive detection, select "user - defined" drive setting and enter the chs values from the table. bios settings (see specification) capacity cylinders heads sectors(unformatted) save the settings and exit the system setup program. ( your computer will automatica lly reboot ) after you configure your computer, you can use the standard dos commands to partition and format your flash disk module , as described below. 3 ) formatting method to partition your new flash disk module with microsoft dos program : insert a boo table dos diskette into your diskette drive and restart your computer. insert a dos program diskette that contains the fdisk.exe and format.com programs into your diskette drive. use the same dos version that is on your bootable diskette. at the a: \ > prom pt, type fdisk and press e nter . select create dos partition or logical dos drive by pressing 1 . then press e nter . select create primary dos partitio n by pressing 1 again. then press e nter . create your first drive partition. if you are creating a part ition that will be used to boot your computer (drive c), make sure that the partition is marked active. create an extended partition and additional logical drives as necessary, until all the space on your new hard drive has been partitioned. when the parti tioning is complete, fdisk reboots your computer. caution: make sure to use the correct drive letters so that you do not format a drive that already c ontains data. at the a: \ > prompt, type format c:/ s , where c is the letter of your first new partition, repeat the format process for all the new partitions you have created. after you format your drive, it is ready to use.
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 5 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) 2. pin information pin assignments and pin type table 2.1 pin assignment and pin type pin signal pin type pin signal pin type 1 /res et i 2 gnd ground 3 d07 i/o 4 d08 i/o 5 d06 i/o 6 d09 i/o 7 d05 i/o 8 d10 i/o 9 d04 i/o 10 d11 i/o 11 d03 i/o 12 d12 i/o 13 d02 i/o 14 d13 i/o 15 d01 i/o 16 d14 i/o 17 d00 i/o 18 d15 i/o 19 gnd dc 20 key pin -- 21 reserved -- 22 gnd ground 23 /i ow i 24 gnd ground 25 /ior i 26 gnd ground 27 ior dy o 28 reserved -- 29 reserved -- 30 gnd ground 31 irq o 32 /iois16 o 33 a01 i 34 /pdiag i/o 35 a00 i 36 a02 i 37 /cs0 i 38 /cs1 i 39 /dasp ( led ) i/o 40 gnd ground
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 6 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) signal descriptions table 2.2 signal descriptions signal name dir. pin description a [2:0] i 33 , 35 , 36 in true ide mode only a[2:0] are used to select the one of eight registers in the task file, the remaining address lines should be grounded by the host. - pdiag i/o 34 t his input / output is the pass diagnostic signal in the master / slave handshake protocol. - dasp ( led ) i/o 39 this signal used either to drive an led whenever the disk module is being accessed or as indication of a second drive present. this signal is active low when the disk module is busy. - cs0, - cs1 i 37 ,3 8 cs0 is the chip select for the task file registers while cs2 is used to select the alternate status register and the device control register. d [15:00] i/o 3 ,4,5,6, 7,8,9,10, 11,12,13, 14,15,16, 17, 18 a ll task file operations occur in byte mode on the low order bus d00 - d07 while all data transfers are 16 bit using d00 - d15. gnd -- 2 , 19,22, 24,26, 30,40, ground. - ior i 25 this is an i/o read strobe generated by the host . - iow i 23 the i/o write strobe pulse is used to clock i/o data on the card data bus into the storage card controller registers when the storage card is configured to use the i/o interface. the clocking will occur on the negative to positive edge of the signal (trailing edge). irq o 3 1 in true i de mode signal is the active high interrupt request to the host. - reset i 1 t his input pin is the active low hardware reset from the host. iordy o 27 t his output signal may be used as iordy. - iois16 o 32 t his output signal is asserted low when this devi ce is expecting a word data transfer cycle.
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 7 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) block diagram figure 2.1 flash disk module block diagram ide interface reset ic data i/o control x tal flash 0 flash 1 flash 2 flash memory controller
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 8 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) 3. interface bus timing acce ss spcifications ide mode i/o access specifications in this true ide mode the flash disk module protocol and configuration are disabled and only i/o operations to the task file and data register are allowed. in this mode no memory or attribute registers are accessible to the host. table 3. 1 ide mode i/o access mode mode - ce2 - ce1 a2 - a0 - iord - iowr d15 - d8 d7 C d0 invalid mode l l x x x high z high z standby mode h h x x x high z high z task file write h l 1 - 7h h l don t care data in task file read h l 1 - 7h l h high z data out data register write h l 0 h l odd byte in even byte in data register read h l 0 l h odd byte out even byte out control register write l h 6h h l don t care control in all status read l h 6h l h high z status out table 3. 2 ide mode i/o read timing parameter symbol ieee symbol min. ns max. ns data delay after iord td (iord) tlglqv 100 data hold following iord th (iord) tlghqx 0 iord width time tw (iord) tlgligh 165 address setup before iord tsua (iord) tavigl 70 ad dress hold following iord tha (iord) tlghax 20 ce setup before iord tsuce (iord) teligl 5 ce hold following iord thce (iord) tlgheh 20 iois16 delay falling from address tdfiois16 (adr) tavisl 35 iois16 delay rising from address tdriois16 (adr) tavi sh 35 note: the maximum load on - iois16 is 1 lsttl with 50pf total load. all times are in nanoseconds. minimum time from C wait high to - iord high is 0nsec, but minimum - iord width must still be met.
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 9 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) a0 - a10 - ce - iord - ioi s16 dout figure 3. 1 ide mode i/o read timing example table 3. 3 ide mode i/o write timing parameter symbol ieee symbol min. ns max. ns data setup before iowr tsu(iowr) tdviwh 60 data hold following iowr th(iowr) tlwhdx 30 iowr width time twi(owr) tlwliwh 165 address setup before iowr tsua(iowr) taviwl 70 address hold following iowr tha(iowr) tlwhax 20 ce setup before iowr tsuce(iowr) teliwl 5 ce hold following iowr thce(iowr) tlwheh 20 iois16 delay falling from ad dress tdfiois16(adr) tavisl 35 iois16 delay rising from address tdriois16(adr) tavish 35 note: the maximum load on - iois16 is 1 lsttl with 50pf total load. all times are in nanoseconds. minimum time from - wait high to - iowr high is 0nsec, but minimum - iowr width must still be met.
hanbit hfdom4 0p - xxxsx url : www.hbe.co.kr 10 / 10 hanbit electr onics co., ltd . rev 1.0 (august.2002) a0 - a10 - ce - iowr - iois16 din figure 3. 2 ide mode i/o write timing example ordering infomation no parts size capacity media transfer mode chip number operation mode 1 hfdom4 0 p - 0 08 s 1 55.3x29.0x0.9m m 8 mbyte byte 1 true ide 2 hfdom4 0 p - 016s 1 55.3x29.0x0.9mm 16mbyte byte 1 true ide 3 hfdom 40 p - 032s 1 55.3x29.0x0.9mm byte 1 true ide 4 hfdom 40 p - 032s 2 55.3x29.0x0.9mm 32 mbyte byte 2 true ide 5 hfdom 40 p - 064s 1 55.3x29.0x0.9mm byte 1 true ide 6 hfd om 40 p - 064s 2 55.3x29.0x0.9mm 64 mbyte byte 2 true ide 7 hfdom 40 p - 128s 1 55.3x29.0x0.9mm byte 1 true ide 8 hfdom 40 p - 128s 2 55.3x29.0x0.9mm 128 mbyte byte 2 true ide 9 hfdom 40 p - 192s 3 55.3x29.0x0.9mm 192 mbyte byte 3 true ide 1 0 hfdom 40 p - 256s 2 55.3x29.0x0.9mm 256 mbyt e byte 2 true ide 1 1 hfdom 40 p - 384s 3 55.3x29.0x0.9mm 384 mbyte byte 3 true ide
|
